電梯門套作為連接轎廂與層站的關鍵部件，其脫落事故不僅影響正常使用，更可能引發人員傷害。這類質量缺陷往往源于多環節管控失效，需從材料性能、施工工藝、環境適配等維度進行系統性分析。

　　The elevator door frame, as a key component connecting the car and the landing, may not only affect normal use but also cause personal injury if it falls off. These types of quality defects often stem from the failure of multi link control, and require systematic analysis from dimensions such as material performance, construction technology, and environmental adaptation.

　　材料性能缺陷是根本誘因。部分門套采用再生塑料或劣質人造石材，其抗沖擊強度與耐候性遠低于標準要求。在實驗室檢測中，合格門套需通過零下20℃至60℃的冷熱循環試驗，而劣質材料在經歷3次循環后即出現微裂紋。粘接劑的選擇同樣關鍵，環氧樹脂類膠粘劑雖成本較高，但剪切強度可達8MPa以上，而劣質云石膠在潮濕環境下強度衰減超過60%。

　　Material performance defects are the fundamental cause. Some door frames are made of recycled plastic or inferior artificial stone, and their impact strength and weather resistance are far below the standard requirements. In laboratory testing, qualified door frames need to pass a cold and hot cycle test from minus 20 ℃ to 60 ℃, while inferior materials will develop microcracks after three cycles. The choice of adhesive is equally crucial. Although epoxy resin adhesives have higher costs, their shear strength can reach over 8MPa, while inferior marble adhesives experience a strength attenuation of over 60% in humid environments.

　　安裝工藝不規范直接削弱結構穩定性。門套與墻體間需填充發泡膠或水泥砂漿，形成彈性緩沖層。若填充不實，空鼓率超過5%即可能引發局部應力集中。固定螺栓的植入深度需達到墻體厚度的2/3，且應采用防松脫設計。實際工程中，部分施工人員為趕工期，省略了螺栓預緊力檢測步驟，導致連接強度不足設計值的40%。

　　The non-standard installation process directly weakens the structural stability. The gap between the door frame and the wall needs to be filled with foam adhesive or cement mortar to form an elastic buffer layer. If the filling is not solid, a hollowing rate exceeding 5% may cause local stress concentration. The implantation depth of fixed bolts should reach 2/3 of the wall thickness and should adopt anti loosening design. In actual engineering, some construction personnel omitted the bolt pre tightening force detection step to meet the deadline, resulting in a connection strength that is less than 40% of the design value.

　　環境適應性設計缺失加劇脫落風險。在沿海高濕度區域，門套背板需具備防銹蝕處理，鍍鋅層厚度應不低于8μm。對于溫差超過40℃的地區，應選用線性膨脹系數與墻體匹配的材料，避免因熱脹冷縮產生位移。某公共建筑電梯門套脫落事故調查顯示，夏季正午門套表面溫度達75℃，而夜間降至15℃，晝夜溫差導致的反復形變最終使膠粘層失效。

　　The lack of environmental adaptability design exacerbates the risk of detachment. In high humidity coastal areas, the back panel of the door frame needs to be treated with rust prevention, and the thickness of the galvanized layer should not be less than 8 μ m. For areas with a temperature difference exceeding 40 ℃, materials with a linear expansion coefficient that matches the wall should be selected to avoid displacement caused by thermal expansion and contraction. The investigation into the elevator door frame detachment accident in a public building showed that the surface temperature of the door frame reached 75 ℃ at noon in summer and dropped to 15 ℃ at night. The repeated deformation caused by the temperature difference between day and night ultimately led to the failure of the adhesive layer.

　　預防體系需貫穿全生命周期。在材料驗收環節，應采用無損檢測技術，如超聲波測厚儀檢測門套壁厚，紅外熱像儀篩查內部空洞。安裝過程實施關鍵工序影像留存，通過二維碼追溯系統記錄螺栓扭矩、膠粘劑批號等參數。使用階段建立定期巡檢制度，重點檢查門套與墻體間隙變化，采用激光測距儀監測垂直度偏差。

　　The prevention system needs to run through the entire lifecycle. In the material acceptance process, non-destructive testing techniques should be used, such as ultrasonic thickness gauges to detect the wall thickness of door frames and infrared thermal imagers to screen for internal voids. The key process images during the installation process are retained, and parameters such as bolt torque and adhesive batch number are recorded through a QR code traceability system. Establish a regular inspection system during the usage phase, focusing on checking changes in the gap between the door frame and the wall, and using a laser rangefinder to monitor vertical deviations.

　　技術升級為安全防護提供新路徑。3D激光掃描技術可構建門套安裝三維模型，通過BIM系統模擬長期形變趨勢。納米滲透型防護劑的應用，使石材表面疏水角提升至110°以上，顯著降低水汽滲透。智能監測系統集成振動傳感器與傾斜儀，當門套位移超過2mm時自動觸發報警，將被動維護轉為主動預警。

　　Technological upgrades provide a new path for security protection. 3D laser scanning technology can construct a three-dimensional model of door frame installation and simulate long-term deformation trends through BIM systems. The application of nano penetrating protective agents increases the hydrophobic angle of the stone surface to over 110 °, significantly reducing water vapor penetration. The intelligent monitoring system integrates vibration sensors and inclinometers, and automatically triggers an alarm when the door frame displacement exceeds 2mm, transforming passive maintenance into active warning.

　　電梯門套脫落事故的本質是質量管控鏈條的斷裂。通過構建涵蓋材料選型、工藝控制、環境適配、智能監測的立體防護體系，可有效降低脫落風險。監管部門應完善驗收標準，將門套系統納入整體電梯安全評估范疇，推動行業建立質量追溯機制，從源頭遏制“豆腐渣工程”的出現。

　　The essence of the elevator door frame detachment accident is the breakage of the quality control chain. By constructing a three-dimensional protection system that covers material selection, process control, environmental adaptation, and intelligent monitoring, the risk of detachment can be effectively reduced. Regulatory authorities should improve the acceptance criteria, incorporate the door frame system into the overall elevator safety assessment scope, promote the establishment of a quality traceability mechanism in the industry, and curb the occurrence of "tofu dreg projects" from the source.

　　本文由棗莊不銹鋼啞口套友情奉獻.更多有關的知識請點擊:http://www.lfzhenli.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from Linyi Elevator Door Frame Installation For more information, please click: http://www.lfzhenli.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message